B26PS((((AAAATTTT22226666CCCCSSSSMMMMCCCC))))GB Operator’s manual 2-27 SE Bruksanvisning 28-54 DK Brugsanvisning 55-79 FI Käyttöohje 80-105 NO
GENERAL SAFETY PRECAUTIONS10 – EnglishSharpening grass knifes and grass blades• See the cutting attachment packaging for correct sharpening instructio
ASSEMBLYEnglish – 11Fitting the P-barrierClip the loop handle with the P-barrier onto the shaft. Note that the loop handle must be fitted between the a
ASSEMBLY12 – EnglishFitting blades and trimmer headsFitting a blade guard, grass blade and grass cutter• Hook the blade guard/combination guard (A) on
ASSEMBLYEnglish – 13• Screw on the trimmer head/plastic blades (H) anticlockwise.• To dismantle, follow the instructions in the reverse order.Fitting
FUEL HANDLING14 – EnglishFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor
FUEL HANDLINGEnglish – 15Mixing• Always mix the petrol and oil in a clean container intended for fuel.• Always start by filling half the amount of the
STARTING AND STOPPING16 – EnglishCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent
STARTING AND STOPPINGEnglish – 17• Choke: Your unit is designed with a 3 position choke: Full choke, half chokeand Run position. Set the choke control
STARTING AND STOPPING18 – EnglishAlways pull starter cord straight out. Pulling the starter at an angle will cause cord to rub against the eyelet. Thi
WORKING TECHNIQUESEnglish – 19General working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot
KEY TO SYMBOLS2 – EnglishSymbolsWARNING! A brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal i
WORKING TECHNIQUES20 – EnglishBasic working techniquesAlways slow the engine to idle speed after each working operation. Long periods at full throttle
WORKING TECHNIQUESEnglish – 21• The cord wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences,
MAINTENANCE22 – EnglishCarburettorAdjustment of the idle speedBefore any adjustments are made, make sure that the air filter is clean and the air filter
MAINTENANCEEnglish – 23Clean the cooling system with a brush annually or more often in demanding conditions. A dirty or blocked cooling system results
MAINTENANCE24 – EnglishBevel gearThe bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you shoul
English – 25MAINTENANCEMaintenance scheduleThe following is a list of the maintenance steps that must be performed on the machine. Most of the items a
26 – EnglishTECHNICAL DATATechnical data (AT26CSMC)Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC dire
English – 27TECHNICAL DATAThe following optional universal attachments are available for use with the specified models.EC Declaration of ConformityIssu
CONTENTS English – 3 Contents Note the f ollowing before starting: Please read the oper ator's manual carefully. KEY TO SYMBOLS Symbols ...
English – 4INTRODUCTIONDear Customer,Thank you for choosing a McCulloch product. You are thereby part of a story that started long ago, when the McCul
English – 5WHAT IS WHAT?What is what on the trimmer and the brushcutter?56141587101181116121321491913244202223241717262527281 Trimmer head2 Grease fill
GENERAL SAFETY PRECAUTIONS6 – EnglishImportantPersonal protective equipmentHELMETWear a protective helmet where there is a risk of falling objectsHEAR
GENERAL SAFETY PRECAUTIONSEnglish – 7GLOVESGloves should be worn when necessary, e.g. when fitting cutting attachments.BOOTSWear boots with steel toe-c
GENERAL SAFETY PRECAUTIONS8 – EnglishStop switchUse the stop switch to switch off the engine.Start the engine and make sure the engine stops when you
GENERAL SAFETY PRECAUTIONSEnglish – 9Locking nutA locking nut is used to secure some types of cutting attachment.When fitting, tighten the nut in the o
Commenti su questo manuale